Malish SPINSAFE Floor Machine Carpet Scrubbing Brush
Malish [732918] SPINSAFE™ Floor Machine Carpet Scrubbing Brush w/ Stainless Steel Guide Plate - 18
Malish [732918] SPINSAFE™ Floor Machine Carpet Scrubbing Brush w/ Stainless Steel Guide Plate - 18
Add to Cart

SPINSAFE Carpet Scrubbing Brush - 18" Dia.

Your Price: $242.71
- Save: $178.01!
In Stock
Your Price: $242.71
- Save: $178.01!
Add to Cart
  • Manufacturer:Malish Brush
  • Product Type:Carpet Scrubbing Brush
  • Diameter:18" Block
  • Bristle Diameter:.014"
  • View All:Malish Brush Products
  • Origin:Made in the USA
  • UPC615129329187

Item Description:

Adjustment screws raise glide plate as bristles wear

SPINSAFE™ Carpet Brush - Fits 20" Floor Machines

The Malish SpinSafe™ floor machine carpet brush utilizes a smooth stainless steel adjustable guide plate to allow the brush to easily glide over the carpet. This protects the integrity of the carpet, reduces drag, and increases efficiency.

  • Adjustable stainless steel glide plate
  • Adjustment screws raise glide plate as bristles wear (Shown Right)
  • Reduces operator fatigue
  • Increases productivity
  • Efficient and cost-effective
  • No break-in process required


  • General Scrubbing: Carpet Scrubbing


Always remove your brush or pad driver from the machine after use. Hang up to extend life. Always clean and rinse brushes thoroughly, especially after stripping jobs. Chemicals can be harmful to skin and eyes.

WARNING: Do not use brush or pad with flammable materials (fuels, solvents, thinner, etc.) or serious bodily harm or injury could result from possible fire or explosion.

Determining Diameters

Block Diameter: Lay the brush on the bristles, block side up. Measure the actual outside diameter of the block (not the bristle flare). See photo below for reference (measurement B).

Center Hole Diameter: Lay the brush on the bristles block side up. Remove mounting hardware, if any. Measure actual inside diameter of the center hole. See photo below for reference (measurement D).

Floor Machine Brushes, Pads, Drivers & Clutch Plates - Determining Diameters

NOTE: Malish brushes are designed to fit each machine as shown, even though the block diameter listed on the charts may vary slightly from the diameter of the block originally supplied with the machine.

How to Break in a New Floor Machine Brush

Before using a new brush on carpeting, the brush should be broken in according to the following directions. This will eliminate possible excess drag by “tipping” the strands, removing any possible burrs caused by the manufacturing process.

Break-in Procedure

  1. Mount the brush on the floor machine. Follow ALL instructions included in your owner's manual.
  2. Find a rough textured floor surface, preferably unfinished concrete.
  3. Operate the machine on this surface. Run the machine DRY for approximately 15-20 minutes. The brush fibers will take a slight set or lean in the direction of machine rotation.
  4. Rinse the brush to remove any dirt caught when running machine. The brush is now ready to be used on carpeting.

Do you want a brush or a pad driver?

If your preference is to have a dedicated product, select a brush. If you have a variety of applications, your choice may be a pad holder. The surface being cleaned and the amount of dirt build-up will help determine the selection. The key to remember when ordering these items is the block diameter in relationship to the machine size. A brush is sized 2 inches smaller than the machine because of the flare of the brush fibers. Pad drivers are specified 1 inch smaller than the machine.

There is an easy way to cross check your selection from the Floor Machine Brushes and Clutch Plates section of this web site.

  • A brush, long-trim pad driver, or short-trim pad driver without a riser, should be 2" smaller than the machine size.
  • A pad driver or MIGHTY-LOK™ should be 1" smaller than the machine size.

Therefore, a 20" floor machine would use an:

  • 18" brush, MAL-LOK™ or PAD-LOK™ without a riser
  • or a 19" PAD-LOK™ or MIGHTY-LOK™

This rule applies to over 90% of the applications.

People Who Bought This Also Bought

   No reviews for this product yet

Please Wait... processing